Welcome! » Log In » Create A New Profile

RE: Autoint finishing wax

Posted by Richard Williams 2 
Forum List Message List New Topic
Richard Williams 2
RE: Autoint finishing wax
July 10, 2006 04:07PM
<HTML>How should I apply this sealant (finishing wax) I am assuming thin like usual also apply with either foam or cotton applicator .
Apply a section at a time or the whole care remove with microfiber or cotton towels guessing microfiber would be better.
Durability 3 or 4 months is this right.

regards stillen</HTML>
Reply Quote
Superior Shine
RE: Autoint finishing wax
July 11, 2006 04:28AM
<HTML>Ask that question here and get a quiker answer-- [www.websitetoolbox.com];



-----------------------------------------------------

Plays in the rain --- www.SuperiorShineDetailing.com
Reply Quote
Ron Ketcham
RE: Autoint finishing wax
July 11, 2006 05:02PM
<HTML>Put it on , thin coat is best, on the whole vehicle, and remove with a terry cloth or microfiber cloth or an orbital or a DA with a bonnett, etc.

Just get it on, thin coat, the longer it drys and cures, the longer it lasts.

And easier to remove when allowed to cure than not allowing it to dry and cure.

Ketch</HTML>



Do it right or don't do it at all!
Reply Quote
Richard Williams 2
RE: Autoint finishing wax
July 11, 2006 08:42PM
<HTML>OK then thanx for the info Ron and Superior Shine the link to the toolbox forum looked like lots of good info.

Just put on car wait 10 to 15 minutes then remove.</HTML>
Reply Quote
Richard Williams 2
RE: Autoint finishing wax
July 12, 2006 12:30AM
<HTML>I was going to edit my post since cannot will post again.

I am assuming that I do not need to apply autoint's One step Polish and sealant prior to the pure sealant for bonding purposes since Ketch did not mention it.

also cotton or microfiber with fieldcrest out of business Martel would be the only towel to use.

regards Richard</HTML>
Reply Quote
Ron Ketcham
RE: Autoint finishing wax
July 12, 2006 04:18PM
<HTML>Whether or not you use the OEM, new name One Step Polish and Sealant, before applying the Finishing Wax is up to you and the condition of the finish.

The use of both is like using the Klasse Twins.

The OEM cleans, does light polishing and leaves a polymer finish.

The Finishing Wax, (actually a polyamino sealant) has no real cleaners as it was developed for the autobody trade and fresh paint.

By using both, you are polishing and protecting.

Using just the Finishing Wax, only protection and gloss.

Ketch</HTML>



Do it right or don't do it at all!
Reply Quote
Richard Williams 2
RE: Autoint finishing wax
July 12, 2006 08:27PM
<HTML>Ron thanx much for the info I may be getting the decon system also will ask about it when I call and order to get the process down and how to keep the paint wet while product is one there either with water or more use of the product.</HTML>
Reply Quote
Ron Ketcham
RE: Autoint finishing wax
July 13, 2006 01:03PM
<HTML>If you or a friend has ever considered getting an electronic paint thickness gauge, now is the time.

We got them on the website, the ETG-1, at an all time low price.

Ketch</HTML>



Do it right or don't do it at all!
Reply Quote
Superior Shine
RE: Autoint finishing wax
July 13, 2006 02:08PM
<HTML>Ron my ETG is acting funny. All it displays is this ---.- and doesn't take readings.

Have any idea what happend?</HTML>



-----------------------------------------------------

Plays in the rain --- www.SuperiorShineDetailing.com
Reply Quote
Ron Ketcham
RE: Autoint finishing wax
July 13, 2006 02:16PM
<HTML>You should contact the guy you bought it from.

LOL!

Buy hot goods, you get what you pay for.

Read the manual, recalibrate, then put in a new battery, if not send it to ProMotor Car for service.

Ketch</HTML>



Do it right or don't do it at all!
Reply Quote
Superior Shine
RE: Autoint finishing wax
July 15, 2006 04:00AM
<HTML>This isn't the one. It is an ebay one but not a former AI unit.

I took it out and had 6 people around me and what happens, it didnt work!!

I tried all that you said.

Yea I will send it in.</HTML>



-----------------------------------------------------

Plays in the rain --- www.SuperiorShineDetailing.com
Reply Quote
Jim Schliebner
RE: Autoint finishing wax
July 15, 2006 11:46PM
<HTML>To get back on topic (cause my guage works fine), we like Finishing Wax just fine. Easy on, easy off, and pretty good durability.

Compares to Meg's #20, if that is relevant to you...

This is a fine product that delivers (important, cause not all do...)

Good Luck.

Jim</HTML>



If it was easy, everybody'd be doing it!
Reply Quote
Richard Williams 2
RE: Autoint finishing wax
July 18, 2006 07:36PM
<HTML>Yes Jim comapring it Meg's 20 is about what I thought proabably about 3 months of durability .
I may try try the Finish Fast product to give it a shine boost where as the Wax just gives a deep lustrious sine.

Yes I do use Zaino but do not use ZFX cure accelerator nor any of the quick detailers they offer Z-6 nor Z-8 really cuts down on the expense but what gets me is paying for the carwash.

autoint's carwash is super very comparabe to P21S exept better than it.</HTML>
Reply Quote
Ron Ketcham
RE: Autoint finishing wax
July 18, 2006 07:45PM
<HTML>Cured Finishing Wax, will provide protection for well over 6 months, it's a Polyaminosiloxane resin system.

The Fast Finish really layers nicely, and adds more protection each time it is applied.

I seldom wash my convert anymore, just Fast Finish it, same with my black Gran Marquis, and they are looking very nice, with no real work.

We have test vehicles running around the city that also have Fast Finish as their trim dressing/protectant, it's holding up on good trim in excess of 2 months.

Ketch</HTML>



Do it right or don't do it at all!
Reply Quote
oli
RE: Autoint finishing wax
July 28, 2006 12:39AM
I hope I don't have this wrong, but are you saying that I can apply the Fast Finish to my black trim without it turning white?
Reply Quote
oli
RE: Autoint finishing wax
July 28, 2006 12:59AM
Sorry, I just realized that fast finish is not a wax. I couldn't edit my post.
Reply Quote
Grumpy2
RE: Autoint finishing wax
July 28, 2006 12:58PM
Fast Finish is a polymer, however much different chemistry than Finishing Wax.

The Fast Finish works great on all trim as well as the paint, even the wheels.

I have also been using it as my interior dressing.

Ketch



Do it right or don't do it at all!
Reply Quote
Doug Delmont
RE: Autoint finishing wax
August 06, 2006 08:17PM
Apply the Finishing Wax to one side of the hood and Mother's California Gold Pure Carnauba Wax to the other side. Then let us know which shines best and lasts longest. That's the way to apply a new product !

Doug Delmont

" If at first, you don't succeed, get a bigger hammer. "
Reply Quote
Doug Delmont
Re: RE: Autoint finishing wax
December 16, 2006 06:35AM
Members:
So far, no one has posted a side-by-side test of Finishing Wax as I suggested above.
I gave the bottle I bought to a pro to try out. He used it but didn't like it. One member here has praised it. One said it doesn't hold its gloss but liked it.
What we need is a careful comparison test. If someone does one, please post.
Doug
Reply Quote
Newer Topic Older Topic
Sorry, only registered users may post in this forum.

Click here to login